B3R Garage: The Mad Scientist's Tranny Troubles

The Mad Scientist has cut, chopped, and welded his 1970 Ford Maverick into submission. We have finally been able to completely drop in the Ford 302 sb into the Maverick using truck mounts. We wired up the starter, and bypassed the transmission lines. However, as easy as cutting into the Maverick was it was about time it cut back!

The Maverick strikes back!

B3R Garage: Troublesome Timing Issues

When you begin to near the completion of custom car that you have never done before all of the tiny kinks and imperfections tend to reveal themselves. For my 1984 Mercury Capri, the problem laid in my inability to understand why my Edelbrock 1406 four barrel carburetor would not idle at all.

Why won't my Edelbrock 1406 idle?

B3R Garage: A Real Winner

A winning car is a little more than dumping a thick bank roll into a project. In fact the definition of “winning” may be diffident for everybody. Some builders find that simply dumping more cylinders into a car in order to increase horsepower makes it better. Others may find that upgrading suspension for autocross makes for a winning combination whereas some find extreme interior and exterior makeovers to be the right direction for their passions. Whether you are looking to tearing up the drag strip, autocross, or take the stage at a car show planning, patience and persistence will be required.

B3R Garage: Shaving Shock Towers

The Mad Scientist has decided to put his 1970's Ford Maverick under the knife again. So far the pre-modified can lighting setup was cut from the rear and replaced with a Torino tail lights. The rear bumper was fabricated from a Ford Mustang rear bumper and all visible exterior mounting bolts were shaved. The engine going into the car currently will be a Ford 302 small block with mustang shorty headers  and a C4 automatic transmission. However, the Mad Scientist has recently got the concept of bigger blocks on his mind. So instead of simply dropping the small block into the the Maverick, the Mad Scientist did a little homework and found out what it would take to put a larger block into the car. As it turns out, the process requires shaving the shock towers!

B3R Garage: Fuel Line Upgrade-Old, Modern, & New

     Year ago when the Mad Scientist was young the normal method for installing fuel lines in any and all cars involved hard rubber hose and steel hose clamps. As the years passed much of the rubber hoses were replaced with steel fuel lines. At the current time there is yet another alternative to automotive fuel lines available known simply as AN(Army/Navy).

     Due to pressure issues with common rubber hoses, routing issues with steel fuel lines the 1984 Mercury Capri will be getting a fuel pump to carburetor fuel line upgrade. Currently, the fuel line from the Edelbrock fuel pump pours into a Mr. Gasket adjustable pressure regulator and gauge before actually entering the carburetor.

     Although the paperwork for the stock replacement Edelbrock Fuel Pump states that it should not require a pressure regulator, it produces approximately 7.5-10 lb. of fuel pressure before entering the pump. The issue is caused when the information about the Carburetor (Edelbrock 1406) states it should have no more than 6 lb. of fuel pressure at any given time. Therefore, a pressure regulator was needed to reduce the flow of fuel into the Edelbrock 1406 carburetor.

Unfortunately, the rubber fuel line coming from the pump into the fuel pressure regulator continues to leak due to excessive pressure and weak hose clamps. Therefore the foxbody Capri will be getting an AN -6 fuel line and fitting upgrade from the fuel pump to the carburetor.

B3R Garage: The '84 Capri Finally Hits the Ground

For a few weeks now my 1984 Foxbody Capri has been giving the Mad Scientist and I issues. However, over the weekend we were able to finally bleed all of the brakes and run the car through the gears while up on jack stands. We were even able to have the car idle on its own for the fist time ever. It was kind of nice to get out of the car while it ran and walk down the road a little just to see how it sounded from a distance.

Unfortunately, after a few time of letting the car idle for several minutes it would eventually die. After this occurred several time the car became very difficult to start and would not idle at all. I could not figure out why my Edelbrock Carburetor would not idle at all. I tried a few thing to hopefully remedy the issue but had no luck. On thing I did was included a fuel pressure gauge following my fuel pump to ensure I had enough fuel pressure. I also put a 2.5" spacer in between the carburetor and intake because it seemed as though I only had the issue after the car got up to running temp. Unfortunately  none of my attempts seemed to fix the issue. So I will eventually be swapping out the Edelbrock Carb for a known good one, and will eventually take the Edelbrock Carb apart for a rebuild.

Here is the video of the car Idling on the ground for the first time.
* I'm actually listening to the Radio in the car.

B3R Garage: 1970 Ford Maverick Update

After a week of waiting the Mad Scientist and I were able to acquire a new heater core and windshield wiper motor for the Maverick. Awkwardly enough Ford Maverick's without A/C have more expensive heater cores than those without. Who knew. Regardless, the folks down at the local NAPA store was able to provide us with a heater core and windshield wiper motor.

After this weekend the entire interior of the Maverick should be completely done. With that being said the car really only needs a few more pieces to reach completion. Unfortunately  the Mad Scientist's truck decided to keel over and die (hopefully for the last time. ). So the Maverick build budget was slightly cut into in order to fix the Mad Scientist's Aspire long enough to get the Maverick done. Although the Maverick street strip build will not stop the build, but it will be extended a little longer.

No offense to anyone following B3R Garage, but it is likely to be in your best interest not to buy a Chevy (s10).